소스 코드
- 게시일 2019. 01. 16.
- Learn how to replace a clutch, flywheel, pressure plate, throw out bearing (aka release bearing), pilot bearing and rear main seal in this video!
My clutch was fine but my throwout bearing was bad so I decided to show how to replace all of the wear items while the transmission was off. This includes replacing the pilot bearing which the transmission input shaft goes into, the throwout bearing which engages the pressure plate via the clutch fork, the flywheel which I upgraded to an aluminum light weight flywheel, and finally the rear main seal because that is a common wear item which causes oil leaks in higher mileage motors. With the transmission out, it is worth it to replace all of these parts now instead of having to do this all over again. Most clutch kits come with the throwout bearing and pilot bearing so you just need to buy a rear main seal.
How to Replace a Transmission (Full DIY Guide): • How to Replace a Trans...
Extendable Ratchet Set: amzn.to/3PzSjOs
Flywheel I used: advanceautoparts.rt8x.net/ORV1AP
Clutch kit I used: advanceautoparts.rt8x.net/2rbKmA
Rear Main Seal: advanceautoparts.rt8x.net/RygRVv
→ Become a ChrisFix Subscriber: krplus.net/usubscription_c...
→ Instagram: / chrisfixit
→ Facebook: / chrisfix8
→ Website: www.ChrisFixed.com
→ My Channel Home Page: / chrisfix
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing.*
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix. - 자동차
![[한글자막]줄리엔강에게 정찬성을 이길 수 있는지에 대해 묻다](http://i.ytimg.com/vi/egrOiiKmRdc/mqdefault.jpg)
![[2024 AFC U23 카타르 아시안컵] 중국 VS 대한민국 풀 하이라이트](http://i.ytimg.com/vi/dcL6YXce6Rs/mqdefault.jpg)
![[Original Song] 우주미아(Would You M.I.A) ㅣ권민&왁파고&티파니](http://i.ytimg.com/vi/cApabFGK8VA/mqdefault.jpg)
I set out to create the most in-depth clutch replacement video in the world! Hopefully the video was helpful!
Tools I used: bit.ly/ChrisFixRatchets
Your channel grow'd so fast...
Yeeees finally i waited so long
Is the supercharger vid coming Next?
Pls doing stuff on opel corsa b pls like 2000.year
Chris fix is better than engineering explained. Why? Step by step. Chris is like a brain surgeon while engineering explained is a emt. Lol.
Everyone: You can't replace a clutch without specialized tools
Chris: *hold my b r e a d*
But then the other guy has the bread now :-/
It should be hold my torque wrench 😂
Alex Savastru 😂😂😂
And Greece
Chris: Give me my b r e a d back
"Honey, that weirdo across the street is talking to his cars again"
lol
"now he's hammering bread into it"
Why the stradman jokes?
Lol
Haha LAMAO
Chris is so detailed I feel like a pro mechanic even though I've never fixed any cars before
I don't know him but as a mechanic I can tell he must not be a layman!
My name is also chris
@@chrisfoster3772 my name is Juan
@@hoodiejuann I guess it takes Juan to know juan
Hey Chris, you are amazing, your videos are always helpful, thanks for teaching
been keeping bread in my toolbox ever since i found this tip. i don’t use it much but it’s developed this nice, blue and fluffy patina.
Might need to swap it out haha
Out with the old and in with new
Chris: "let's replace our clutch"
*rebuilds entire transmission*
Liam Johnson when he replaced the whole transmission I laughed so hard
@@brianj1203 same 😂
at least hes not doing a half ass job
"gently used mustang for sale, all routine maintenance performed."
True, he does go the extra mile
Do I have a car? No. Will I replace my clutch myself when I get a car? Probably no. Did I watch the video. Yes
Ha!
Just like those cooking channels.
Me with all his videos lmao! He's just entertaining to watch.
Karl Leego i only watch it for satisfaction
Same here,I'm just fascinated of how clutches work
I love how you take a scary and intimidating job, and turn it into a super simple process that's not daunting at all.
I've rebuilt my suspension, engine, transmission, new clutch, rebuilt my diff, etc. All cause of you. My car is track ready BECAUSE OF YOU. Thank you Chris❤
Can I ask you what car have you rebuilt? Because I'm trying to basically to the same thing/try to diagnose and repair my car when when something will fail. My car is an audi a4 b5 1.9tdi 2000
@@Atomicul My track car is a 1998 Mitsubishi Eclipse GSX. 2.0 4G63T, AWD, 5spd manual.
Bored/forged block, built and ported head, injectors, big turbo, rebuilt both diffs and swapped rear to an LSD. Threw a bigger fuel pump in it. I'm in the process of bolting on the bigger turbo then it's off to the dyno to have it tuned.
I daily a 2010 S4 and it's stage 2, intake and supercharger pulley.
@@cody6571 sick
@@cody6571awesome man, I’ve been rebuilding my 3000gt VR4 and have learned everything as well with it.
While my clutch is a little different and my transmission way smaller, this definitely gave me some useful tips for replacing my clutch! Just got done putting it all back together
Awesome! Glad the video was helpful and nice work!
When you buy 2 pilot bearings.. just so you can show the viewers both extraction methods. We love you Chris. 👍🏽😎
I want to make sure everyone can follow along no matter what! Thanks a lot!
He should had use the bread method on the first one. The second one being brand new came off easily while the old one was seized in place.
Good luck trying that on an old seized pilot bearing.
@@Napoleon_Blownapart
1) Your username sounds kind off strange( I know who Napolean is)
2) At some point the pressure will be enough to pop out the bearing.
@@Napoleon_Blownapart idk man maybe u should test it
@@Napoleon_Blownapart Napoleon Blown Apart lol.. Napolein Bonaparte.
"Mom i need bread"
"Why"
"Its for my car"
mom: Jesus johnny ur becoming like the neighbors kid next thing you know ur gonna be talking to ur cars😤😤
cars need to eat too you know
@@Kyle-kv6ur Lollll
kids in africa :( :D
Me: **walks into the kitchen to grab bread**
My wife: "ohhhh no no no not the my favorite bread again"
4 years later and this video still hits. LOVE YOU CHRIS. You inspire me to be a mechanic when I get older
How you can remember to explain so many steps and details is amazing. At my age, (64) this would overwhelm me. I’m also a woman, and did not grow up working on cars. This is why boys AND girls should start learning mechanics as CHILDREN!
750k views in 2 days for a video on how to change a clutch, in a country where almost everyone drives an automatic.
Well done !
Great quality stuff.
Thanks!
Amazing
@Wolf Most of his views are from Europe
KRplus is not exclusive to the US
Nem todo mundo é dos EUA 😅
I don't even own a manual transmission. Why am I watching this?
Because now I could fix it just from watching this.
You're an awesome teacher sir.
Thanks man
After the transmission video I was ready to do the job. My cars transmission is fine 😂
Who else remembers back in the day where this man @ChrisFix had trouble installing a windshield?
I love being able to see his improvement over the years.
4444444 440440
@@keronmoses4867 ok lol
@@Brain-Lag what did keron say?
@@chrisfoster3772 i didnt get to see either sadly
@@Brain-Lag what do you mean you didn't see you replied to it
Just wanted to share that because of you Chris I was able to do this job on my 01 Silverado. I’m no mechanic by a long shot but you put it in a manner that is understood. Huge thanks for these videos and the amount of organization that goes into them. Keep doing what you’re doing sir!!
@Adrian De La Garza Jr WOW! Impressive! Congratulations!
Hope I don't have to do it my s10
I was going to try this on my '03, but being my only means of transportation, I was absolutely certain there would be some part or tool I would need in the middle of the job, thus stranding myself.
@@thzzzt that's why I recommend watching the whole video first, then doing the work. Sometimes Chris forgets to mention something before he does it. Because of this, I tried to take my radiator cap off my subaru while it was warm and it didn't work out well...
@Asmith 1111 how badly did you get burned? Hospital bad, or run it under cold water for a minute bad?
Why we love chris?
He makes everything simple.
He's saves everyone money.
He's makes us learn more.
And this is pure entertainment even for a non car guy
Edit: 4 years later got a Lexus IS and I am now a car guy who enjoys working on my car :)
Until you actually go work on your car and you realize that things rarely come apart this easy.
9
@@xesior actually no I just heat up the bolts
LegacyGameplays why i hate chris but secretly really want to be him
He makes everything look so easy when i do it so streasfull and hard
He saves loads of money
@XsR just take a grinder to it
Friend: “Dude, why do you have bread in your tool box?”
Me: “Bro... pilot bearings.”
Friend: “Gotcha.”
Where the fk does he learn this stuff?
thats too good bro im dead
@@RatusMax Something called... THE INTERNET
i visualized that
I've done the grease trick, never used bread though...
Save this man at all costs. He's worth his weight in gold.
Some other tips to supplement this great video:
1. Even with the alignment tool, if it’s a plastic one, the clutch disc will likely sag a little. So before you tighten the pressure plate bolts, make sure the alignment tool is centered in the pilot bearing and level.
2. Some transmissions will have a small amount of play at the input shaft so do some research before buying a new
tranny if yours has end play.
3. Another trick to lining up the input shaft to the splines, is manipulating the gear levers and put it in gear then rotate the rear tailshaft until it lines up and fits in. This causes the input shaft to rotate. Then put it back into neutral as you push it in.
4. Don’t hammer in bearing pilot bushings!
What if Chris Fix is just a pair of arms and a mouth?
I saw him irl
RassuGaming123 did he only had arms and a mouth?
@@puertoricanartist2555 nah, he's a normal humanist just like us.
@@razman8241 woosh
With a built in camera in the forehead
4 Steps to fix your car. 1 get out of the car. 2. open the hood. 3. YELL."HEY GUYS CHRIS FIX HERE". 4. Success.
Forgot the *Snap yo fingers
LOL just imagine it working like that
Lol
step 5 bread step 6 tasty success
Legend has it, if you say "hey guys" three times ChrisFix will appear to fix your car for you
22:52 "We want the end of the alignment tool to go all the way into the pilot bearing and that will hold the clutch in the middle for us."
The first solo clutch job I did was on a lift. I didn't have a cart or table so my pressure plate was on the floor by my feet. I installed the clutch plate with the alignment tool, picked up the pressure plate from the floor and as I stood back up the falling clutch plate struck the bridge of my nose while on its way to the floor, where it was chipped against the concrete. Live and learn!
As always, thank you for sharing and stay safe!
As an SN95 owner, thank you sooo much for taking some stress out of doing a project like this.
How did it go? I'm about to do this job on my new edge
@@jessepickar3297 I just started, got it jacked up and the tranny off, just waiting on the new parts and some tools to come in this week so I can do the rear main and everything else down there. Putting a spec stage 2 in my 97 cobra. I'm gonna be honest, the list of things you need for a clutch job is verryy extensive if you don't already have the tools/fluids etc. I could list it here if anyone needs. Chris does mention a lot of stuff throughout this video and the other clutch video that I just had to write them all down since I was lacking in some tools and all the fluids, and also found myself picking up a few more things on top of that. I love new edge stangs, what are you dropping your tranny for?
@@jessepickar3297 I've watched this, and the clutch video multiple times and it made doing this project so easy. It gave me the confidence to do it myself 100%. Thankfully sn95 owners have a content creator like ChrisFix. Now when are we getting the supercharger video? lol
MomFix- Where’s bread?
ChrisFix-In my clutch
😂
And for his next trick, Chrisfix will show how to use a pizza as a spare tire. (deep dish works better....more tread)
@@junkstough6622 soup as transmission fluid
@@junkstough6622 Dr.Pepper as coolant
Club soda as brake fluid ha ha just kidding u shouldnt do that. That would destroy the engine.
The grease and bread method for removing the bearing from a blind hole puts you on a whole other level of wizardry.
Idk that worked
hahaha
Can i use bread and butter so i won't waste it after i pulled out the bearing🙄🤔🤔🤣🤣🤣
I've done it with just bread, it looks like it was a lot easier than the grease/bread and less mess!
Best wearing tools removed bearings
I love your video series... each one you breakdown the job at hand in chronological order and in simple language... Thank you for sharing your expertise with great knowledge and enthusiasm.
Thanks Nathan.
The way you set up your videos and take the viewer through all the steps is extraordinary. Thank you.
I'm sorry I didn't catch all that the first time, could you please go over it again but this time use my 98 ranger as an example? I promise to watch more closely!
Hahahaha I need to do my ranger. I don’t even want to bc the exhaust is rusted to bits
ChrisFix even more of a reason to do so my dude
Rangers are pretty easy to replace the clutch, just did my 93 3.0, i didn’t remove the y pipe thinking it wouldn’t be in the way so i unbolted the transmission and found out I couldn’t lower the transmission enough, should’ve removed the y pipe first and would’ve made taking the bell housing bolts a lot easier too
@@chrisfix Do a new exhaust on the ranger ;)
@@chrisfix straight pipes
I have changed many clutches, I still watch for the tips and little tricks. I defiantly learn a few things everytime. Thank you Chris!
That is exactly what I like to hear! Thanks for the support!
After watching your video, now I can brag to my friend about how I repair my clutch...even I do not even own a car yet. Looking forward to repairing the speedometer
Haha I am glad you are learning a lot!
I'm honestly impressed by the time and effort you put into these videos man, keep it up!
You have been the biggest inspiration for me to become a mechanic when i can get a job. Every video you make makes fixing cars look so easy and by following every step of yours it actually is. When i help my dad fix his car when there is something wrong with it, then I will bring out the knowledge what you have given me. My dad was pretty impressed when i found the problem. I am really grateful for your videos and you truly deserve way more subscribers than you actually have.
same im only 13 and you got me into cars and when i told my dad (he’s a mechanic) he got extremely happy so yeah Chris you just made a family happy doin what you love keep it up
Chris, one of them guys that becomes happy when something breaks in his car.
"These bearing removal tools are the best thing since sliced bread!"
ChrisFix: *not* *so* *fast* *there* *buckaroo*
I want to live in a world where every car job goes as smoothly as it does in a Chris Fix video.
Hey guys ChrisFix here and today I'll be showing you how to rebuild your transmission. All you'll need is some warm soapy wooder, medium strength thread locker, and a potato...
30 mins later
And that's how you do a complete transmission rebuild.
Me: damn this guy is good
Lol love your videos. very thorough
Haha thanks man!
Emilio Valdez you forgot the common hand tools!!!! 😂😂
Read that all in his voice 😂
Pilot bearing: You can't defeat me
ChrisFix: I know, but he can
*bread comes crashing in*
Loool
Memes of the century😂
I just wanted to reach out and tell you how awesome you and your videos are for Diys. Being a female , mechanical skills normally are not on my resume but repairs are so expensive I have learned to do many of them myself and finding a video that breaks it down well enough for this to be done is more times than not very difficult , and leads to many trips to the library or hours of searching on line with taking bits and pieces from each source and tackling the job. Your videos always break it down to where I can understand it and you show every step many times I will search your videos and I do it with your video kinda like we’re doing them together like hands on lol. Like the clutch video , it saved me hundreds of dollars and hours of stressful searching. Thank you so much and don’t stop teaching guy it is your calling. .
@brendasmithazgirl2 Kudos to you for repairing your own car! My brain can’t keep up!!! Maybe if I listened ten times and transcribed this video, I MIGHT be able to do what he did!!!
Chris, I can't thank you enough for these wonderful videos. I myself is a student who just acquired my first car, and with not a lot of money on my hands, these videos really help!
Next video: how to install new engine with a banana.
lol
Up next: Using milk as brake fluid (100% works!)
Hella funny
Hes so smart.
@@salteengamer4799 It did work.
*How to replace a clutch*
_Use bread_ 😂
Lmao
I actually checked the calendar... Chris and his April 1st jokes!
-_-
I definitely checked the date as well when I seen the 🍞
Dude, your clutch is toast!
Thank you for adding all the cleaning tips- I am going to be replacing the clutch and all pieces on my 99 Miata next year, and wanted to do it on my own. this video was extremely informative simply because the information translates to so many different cars.
I am so thankful for your videos. They're so clear and packed with information while remaining efficient!
waiting 1 month for a 3 minute video 👎👎👎
waiting 2 weeks for a 30 MINUTE video.👏👏👏
@KamekoBruns I can't even use my legs and I'm watching this video.
I Don't hear and i'm watching this video (No subtitles :( )
Well I’m dead and I’m watching this video
I'm an alien and we don't have cars AND I'M WATCHING THE VIDEO
I am Pi, and I am here to watch the video that rivals my infinite knowledge.
When he started pouring bread in that seal, I was like, "wait a minute, it's not April 1st, is it?"
But it all makes sense
Seen it done with a rag also. All it has to do is stop the grease from squirting out around your tool - that way, the only place for it to go is behind the bearing.
A bar of soap also works
Rag is less malleable, so might be able to do it sooner, and without quite the mess. @@aussiebloke609
_Usually_ less mess, but harder to get a good seal sometimes, especially if the cloth is too thick. Remember that it has to fit between the inside of the bushing and the outside of your pushing tool without too much friction, or you'll just wedge it all inside the bushing - but without too much extra room or it just won't work. But it's an option if you don't have bread handy. :-)
I did say "without quite the mess", not "without any mess", for a reason. ;P@@aussiebloke609
Chris is seriously a hero of the car community. My accord 5 speed needed a new clutch and this video walked me through the entire process and I saved so much money, auto shop quoted me 600 for the labor and 300 for parts and I ended up saving almost 700 just by DIY (psst. Really good first car wink wink)
I’ve worked on cars for 35yrs and never seen or heard of that grease and bread method to remove bearing. Amazing you can learn some new everyday!
You need to put a Chris fix exclusive wrap and a body kit on the driftstang
Yeah a really cool racing livery would be awesome
Bradley_Jemison idk I kinda like the clean look it currently has
imded I like the red but I feel like the body needs a more aggressive look
Bradley_Jemison ya I agree it would look so meannnnn and aggressive
Bradley_Jemison a wrap would be cool but I think the car looks good as is in terms of the body... the only thing is possibly the spoiler but that still looks really clean
Chris saved my dad $2000 from this video, you know what you can buy with $2000?
4000 bottles of *soapy wooder*
lol
Omar Babovic a new son
and a lot of bread and grease!
Chris has to be from the tri state area
A car. Really, I paid $2000 for my 96 Mustang GT.
Chris, your attention to detail is second to none. If an individual has problems understanding your videos then they have no business messing around with any machinery...especially a car.
Thank you Chris for taking the time to share your knowledge and experience with us.
chris fix: so now we are doing an oil change
video: since we are disassembling this, might as well rebuild the entire engine
LMAOO
Chris "oh man, this transmission is shot!"
Me " he didn't see that coming I see"
Chris "Out with the old, in with the new"
Me "of course, it's Chris"
True
Chris: "let's replace our clutch"
rebuilds entire transmission
Dude that was awesome....little tricks a mechanic cant even think about...a bread can make your half work done....👍👍👍
Having a lazy morning. Time to watch someone do a lot of work and make it look easy. Satisfying coffee time.
*How to replace your car's clutch*
"OKAY, WE'RE GONNA THROW OUT THE TRANSMISSION AND BUY A NEW ONE"
Lol
That’s what I said!!!
If used sport clutch plate, the flywheel will need to replace soon.
exactly what i thought 😂 because transimission bearing aren't replaceable
but dat shaft has alot of play tho. wat do you there?
Wow my jaw dropped on the floor. Thought you’re doing an early April fool episode while you show us the piece of bread.
I HAVE UR JAW COME AND TAKE IT
I just started school for auto tech. This channel is so awesome! I like who you explain everything. It helps noobs like myself, who have no clue what I’m looking at. Thank you, ChrisFix!
Thanks so much chris. My clutch in my 1988 ford ranger is slipping really bad in 4th. This video goes into really nice detail. Love the at home diy methods of doing things too.
How are the Honda's holding up? Can we get an update on them.
YES !!!!!!!!!!!!!!!!!!!!
He sold the civic that his neighbor gave him. (I've seen it in his ig story) but yeah. He only has a del sol now
@noah wolfman its a late upload so you can clearly see the civic. Try to follow his ig because he has a lot of update regarding his drift stang and other car related review. Lol
I would like to know too
@@GX2re on his instagram he showed selling the civic. If you want to follow him, it is in the description. You can see it in the video as the filming length was so long.
Hey guys crisfix here! Today we will be doing open heart surgery using common hand tools!
Everyone: You can't replace a clutch without specialized tools
Chris: hold my b r e a d
😂😂😂😂
@@novellamoores9387 copied lmao
Lol
@@novellamoores9387
Only pilot bearing need tools.
Clutch can be replaced without them.
Bro you legit have single handedly taught me more about fixing my cars in less than a month than my mechanics teacher did in a whole year in high school.. I only knew basic things like spark plug replacement and big easy to reach things like radiators, fans etc.. Never once did he show us how to actually take apart an engine to get to things like the pistons or crank shaft or even bothered lifting any cars to try and show us transmission work 🙄
Thank you 🙏 been a long time subscriber for 4 years and now final got my antique dream Jeep. This vid helped with dropping the transmission and clutch
That is awesome!
Ted, what year and model is your Jeep?
@@vigilantemotors 1980 cj5
@@tedman2535 Nice, very nice! A bit jealous over here lol
if only it was as easy as you made it look lol, no siezed bolts, no bloody knuckles, no swearing 😂
Right! 😂😂😂
mhmmmmmm
Swearing itself is good and healthy, nothing beats neutralizing an alarming anger level than a well pronounced swearword.
@@SE45CX 🤣
You don't know pain until you have a starter from a 73 mustang drop on your balls
Still don't own a car. Still watch your videos.
Thanks for convincing me to become a mechanic, even now as a mechanic your videos help so much you make this simple and great, I just love it!
Chris is such a huge inspiration to me! Started watching him 2 years ago and now Im an auto mechanics. Time does fly! ❤
I appreciate all the efforts you put on to make this video available. I can't imagine how you did read many instruction materials, how many hours you've spent behind the screen to collect many many footage to create this ultimate guide. Greetings from Iraq...
Thanks so much! It does take a lot of time and effort but the end result and comments like this make it all worth it!
Thank you Chris,
I just changed my clutch in the middle of the mountain with a simple set of tools i had in the car..
Was not so easy and i am all dirty.. But i did it and it works..
Great job sharing your knollowge with so much quality, you do it really good ;)
Your productions are exemplary; simply amazing. You’re a very gifted young man indeed
Chris, you should make a 'dont ask me how I know' video showing us how it is you know
Hahaha that’s actually an awesome idea!
When ‘how to install a clutch’ turns into ‘how to replace the whole of your transmission’
And a rear main seal.
😂😂😂😂 but it's simple at home tools is all that's needed
@@valjean2036 simple but difficult.
@@valjean2036 I couldn’t do it since I’m all out of bread
Thank him
Chris your vids are always informative, comprehensive and enjoyable, cheers
Chris, i do not own a truck as EU citizen, but your videos relaxing me how good you are explaining this, even noobs can fit new stuff on their trucks
I don’t even have a car yet I still watch these videos 😭🤷🏽♂️
Same story with me😭
same man
Gotta dream! With out dreams you have nothing. Check out my 99 trans am ws6.. Ill be doing some really cool upgrades hooker headers, tick master cylinder, BMR pan hard bar/lower control arms/subframe connectors, umi coil overs! To much to list! Already have all the parts. Ill be uploading a new video every Saturday.
same here bro :D
This is the ChrisFix effect!
When he said grease and bread I thought this was another April fools
It actually works very well!
I’ve done it for some plumbing work too you’d be surprised jajaja
What did the bread do to deserve such injustice? Getting stalled? Lol
@@minty3575 jajaja?
me too lol but after seeing that I was like niceeeeee
This video is perfect !!! Absolutely packed with information. no antics or nonsense. Thank you !!
I can't be the only one just looking at those videos even tho I don't have a car and don't need to fix anything... Its just great to know more and more about cars and fixing them!
I’m pretty sure 95% of your regular viewers already know how to do most of the tutorials or have no intentions on ever doing doing it. There’s just something so meditating about listening to you explain things haha
Me who just bought a Mach 1 that needs a clutch cable and throw out bearing 👀
Cop: sir do you know how fast you were going
Chris: no. Me spedo broke. Fight me
HEY GUYZ ITS CHRIS FIX HERE. TODAY WE'RE GOING TO FIX MY FRIENDS SPEEDO
Being a car guy.. wow. So entertaining AND informal.. , love your work Chris!! You're better than my instructors. =)
Bro, this has got to be the best descriptive how to videos I've experienced. Thank you a ton
this guy is skilled bruh, he held the camera in his mouth while making this tutorial while speaking in such details
Akutø 7k AND speaking clearly all at the same time
Owns an automatic, still watches... great upload.
Its two AM, I can't sleep, I don't need to work on my clutch but still watched the whole thing. All your videos are just so informative and entertaining. I love it.
I have a broken throw out bearing in my 1942 GPW, ordered these parts for it but not being a mechanic, this video was super helpful! Thanks Chris 🙂
That's a cool car! Let me know how that job goes!
@@chrisfix Thanks! I worked on this car with my dad 30 years ago, and recently inherited it so it’s very special to me besides the history of it :-) I’m currently waiting for all the parts and good weather because my garage is just big enough to park it in. I’ll let you know how it went!
Officer: Do you know how fast you were going?
Chris: No
Dont get but that makes it funny
@@joejoe-cv4vp his speedometer don't work watch until the end
@@rebelson4617 i think he forgot to install the speed sensor :)
@@makern5304 either that or the speed sensor is bad he said he's gonna make a video on it
@@rebelson4617 yea or he didn't put it in just to make the video
ChrisFix your videos are beyond professional T.V. grade quality. I can't believe how much time and effort you put into making them. They are TOP notch!!
Do you think you could start adding in a ROUGH estimated time needed for the jobs (ex. 4-6hrs, 1 day, a whole weekend, etc)?
Yes, I agree the only thing missing is the time spent. Considering this took two separate videos I am guessing at least 16 hours or two days. It is a huge job and expensive if someone else does it for a reason. Amazing job.
Thanks a lot!
@@chrisfix No, thank you! I am a bit of an amateur car enthusiast who just moved to another country so there's not many people I can ask for assistance around here. When I need to do some repairs on my vehicles, I ALWAYS first come to your channel as it us by far the best (in quality and content). You have saved me heaps of time, money and frustration. Luckily I do have an extra vehicle so time isn't that much of an issue but think it will be extremely valuable to have a rough idea of time so my wife don't get pissy when I tell her it's a 30min job and then only emerging from the garage after many days? Weeks? Months? Oh shit, it's been 4.5 months, gotta go, cheers! And thank you!
Tyler
Rough estimates don’t really work well. I’ve done work that was estimated to take the whole day in half that and other times where it was supposed to take an hour or two takes half a day. It’s all up in the air really and for some reason customers get frustrated when it’s out of your control. Shit sucks.
It would also be nice to put an estimate on how my you could spend on replacing the parts
12:11 that transition was too damn smooth. I'd struggle making a transition that smooth by keyframing.
Love how good you explane every step you make! Great video
me: bread and grease yeah right... me 7 minutes later: (surprised pikachu!)
Lol
I don't remember where I saw it (I think it was on an episode of Roadkill), but I heard you could also use something like a bar of soap or candle wax. I just think it would be a little less messy, and also less likely to seep out the small gap between the bearing and the dowel/rod/whatever your using.
@@Calebguy13 it was roadkill. basphemi vs super bee episode. and Finnegan used Irish spring for his peeps
Great video Chris! One super important thing to note for many modern vehicles, if there is a tone wheel for the crank position signal on the flywheel you MUST clock the flywheel properly or the car will NOT start. Learned that one the hard way and I've seen professionals make the same mistake. Like/Pin this post so people don't make the same mistake!!!
Thanks for the tip!
Just one more part added to try and keep the DIY'r down.
This was super helpful! I have a bad throw out bearing in my sn95 and had no clue how to fix it. I saw the sn95 in the thumbnail and I knew this was the video for me. I learned so much about my car thanks to this video!
Today I'm also going to the garage to change the clutch on my car, I honestly like what you do, I like how you work, you're a skilled mechanic, continued success
This channel continues to be an asset to KRplus and every car DIYer.
The amount of effort you put in and how in depth your videos are is mind blowing. Greatly appreciate you and your videos
Thanks and I’m glad you recognize the work that goes into it!
Slide hammer would work to remove the pilot bearing too but I have never seen the bread and grease method. Brilliant!
Dude, you are good if you are not making money by posting videos you should. One of the best videos I have seen lately. You get right to the point and talk only about what needs to happen. Short and Concise. Also you have a good radio voice. Keep up the good work.