The vertical boards were sprung out at the top because of the flat top board. If the bottom and center board had been horizontal the vertical boards would have been straight. Look at how the vertical boards are the top plate.
I think they are upgrading fence planks if not there is no other logical reason or they are taking a easy way for removal of planks in stead of a bunch of nails laying everywhere
He’s not cutting it too low people. The top rail is t shaped and the bottom rail is 2-2x6’s sandwiched around osb making it a very strong beam and since the top rail is t shape there’s a fence on the other side so nobody has the back of the fence yard calm down about the top cut because he’ll come back with a trim piece hiding the cut and locking the fence top in. It’s a production type fence for if you’re paid by the foot each day you come up with a simple but sturdy design and all you have to do is dig a hole for the run and shoot two parallel lines
Remember to use a nose and face shield. Fine wood dust are sucked up into the eyes, nose and mouth. They cause irritation of the lungs and can be severe.
THAT'S PRETTY TIGHT BUT IF YOU WANT TO DO A CUSTOM SCALLOP TOP CUT BOWED UP OR BOWED DOWN YOU CAN TAKE A 15 FOOT LONG FLAT THIN FIBERGLASS ROD AND TAP A NAIL ON ONE OF THE 4×4 POST ON ONE END AND THE SAME EXACT THING ON THE OTHER POST ONE INCH FROM THE TOP OF THE POST MEASURING DOWN FROM THE TOP OF THE POST AND TAP IN NAIL ABOUT HALFWAY AND THEN TAKE YOUR FIBERGLASS ROD AND IF YOU WANT DOWN SCALLOPS THEN GO TO THE CENTER OF THE SECTION OF THE FENCE AND TAP A NAIL AT THE CENTER POINT ONCE YOU'VE PULLED DOWN THE FIBERGLASS ROD TO ACHIEVE THE SCALLOP SHAPE AND TAP NAIL IN TO HOLD THE SCALLOP SHAPE AND TRACE YOUR ROD FROM END TO END WITH A GOOD PENCIL AND ONCE YOU DONE THAT THEN REMOVE FIBERGLASS ROD AND TAKE YOUR SAW AND FOLLOW YOUR LINE CUTTING FROM END TO END AND WHEN YOU GET DONE CUTTING YOU CAN STAND BACK AND LOOK AT YOUR NEW SCALLOP CUT FENCE AND JUST REPEAT IT ALL OF THE WAY AROUND THE WHOLE FENCE GOD BLESS ✝️✝️✝️
I don’t think any of you looked at the way the fence was constructed, there’s a backer rail below the top rail that they want to make the fence seamless for that style of fence.
So then, won't you please explain to me, how is it covered by the top broad? The top rail is next to it, not on top of it. I take it you work with these illegals?
Having done fencing professionally, this was pretty cool and saves time on this type of fence build. The bottoms are nailed first, the tops stick up and are not nailed yet. When hes finished, he will come hack nail the tops and add a piece of trim horizontally along the top when they are finished.
Because that is what the home owner ask for. No way would he be adding the extry labor had it not been requested by the person requested it and paying for his esrvice.
I agree, to me, the fence looked better before it was trimmed however it’s not my fence and I bet the customer was extremely happy with a job well done😎
1) There must be a fence height restriction. 2) He had better be putting a piece of trim under that t-rail on top because that huge gap looks like shit.
Normally, you would cut the bottom of the board to maintain the dog-eared finish at the top, but this is a picture frame fence, so there will be a finishing board placed on top.
Если бы 7 раз отмерил, то можно было не соезать. То что срезал, теперь в утиль. А правильно бы омерил, то собрал бы ещё может 3 п.м. забора. Жопарукость.
Look at it more closely. It goes under the top plate. They put the em on long with the tops bowing out. Watch as he cuts, the cut fence boards straighten out to be under the top plate. You can disagree on which looks better, but the top plate is objectively better for the lasting longer. The top of the fence boards is end grain, which soaks up water and leads to damage over the long term. Covering the end grain will make the fence last much much longer.
Cuando las cosas no están bien medidas aky el pretexto romper y tirar lo k era útil como una barda completa con esos cortes k tenía cada tabla K DIRIA EL DUEÑO , ya k la madera es cara aunke está sea de 3a (por los muchos nudos k lleva)
Это надо же ради видео так заморочится закрепить доски по один уровень позади рейку закрепить под уровень и потом пилить циркулярной пилой с направляющей
The fence is not short this is a design they will cap the top and stain it or paint it and it will be a pannel style 😊 great work my friend perfect technique
There maybe many reasons to cut it down, but I can't understand why they didn't leave it like 75mm (3") longer to keep the top stringer covered? Looks to me many mistakes probably got made on this job
А ни кто не заметил, что забором ограждают рабочую зону ? А доску на забор видимо закупили такой конфигурации. А для рабочей зоны, декор не нужен и забор должен быть типовым. Может по этому и делает обрезку. А ещё и рабочие с своеобразным мышление , по поводу красоты забора....😅 У меня других мыслей нет......😅
Были красивые верхушки забора, теперь просто палка...
Vero l'o visto è l'o scritto pure io, prima Era più bella.🧐🤔
@@francescocastiglione4643 🤣
That's the part of the fence that touches the ground.
Когда будешь строить себе, сделаешь как надо.👍
😂😂
Наглядно показал как очень быстро можно все испортить 😂
Я бы тоже оставил
❤
@@KirpalsinghRawatthats what small trim hides
Great job 🎉❤
It looks like he just cut the fencing short.
The taller the fence the better. Good fences make good neighbors
Wish Biden knew that!
So do Border walls
Ни ума, ни фантазии
I wonder if they fired him for screwing up the fence
Инструмент хороший конечно. Но здесь до обрезки забор был красивее.
That's what you call a skill saw er 😂 he did a great job. They hired him to do the job how they wanted it and it came out looking very nice👍
Der Nachbar hat sich aufgeregt, das der Zaun 6.3 cm zu hoch ist.😅
Absolutely agree
I agree with you!
😅😅😅😅😅
Такой красивый забор БЫЛ!
Гнить хорошо будит😮
Я с тобой согласен
Возможно они и делали его таким,но заказчику хотелось иначе...
Now it's bueautifuler n straight 😮
@@user-mf4oz8bb6wили не заплатил😂
Io non li avrei tagliati, perché prima la staccionata appariva esteticamente più bella senza essere accorciata.
Так несколько раз ...и можно новый заборчик ,ляпать.Зато проверил диск ,на чистоту реза...☝️🙂
Looked nicer before the cut.
Agree ! 👍
La regò.
Cortò below the 2x backing
And harder to climb… not sure why they cut.
Yo Yo Carpentry ps iis more level 👍😊
Oops its
А нахера?)>) Так красиво и повыше было
He who pays the bills makes the rules. Probably what the homeowner wanted
Госты по высоте. Косяк исправляли 😂.
Им самим обидненько 😢
@@albertscubciks883правила очередного ТСЖ , кооператива,...😅
Ес ть идиотские нормы высоты и даже "прозрачности" Заборов.
по нашим ценам этот забор,дорогое удовольствие!😮
Respect
Nice. Now there's a gap at the top and the faces of the boards aren't anywhere near flush to each other. I'd reject that if it were my fence.
Same here. I build fences and this is NOT the way
Trim board gets nailed across the tops to hide gap and hold boards in place. You can see the other side at the end of video.
They have to nail the boards at the top now
Было красиво, фигурное навершие... Зачем спилили?
The vertical boards were sprung out at the top because of the flat top board. If the bottom and center board had been horizontal the vertical boards would have been straight. Look at how the vertical boards are the top plate.
The shaped top is called “dog ear”
@@donkeziah2564ну теперь все понятно
Чтобы забор не портился от дождя. Легче конёк поменять , чем весь забор🤷♀️
I think they are upgrading fence planks if not there is no other logical reason or they are taking a easy way for removal of planks in stead of a bunch of nails laying everywhere
Было красивее. Не надо было отпиливать
😅😅
Дрова нужны !😊
😂😂😂@@evgeniysemenov6429
Lo mismo pensé!!😊
Как дониво достучадся .Это тип касяк порит
He’s not cutting it too low people. The top rail is t shaped and the bottom rail is 2-2x6’s sandwiched around osb making it a very strong beam and since the top rail is t shape there’s a fence on the other side so nobody has the back of the fence yard calm down about the top cut because he’ll come back with a trim piece hiding the cut and locking the fence top in. It’s a production type fence for if you’re paid by the foot each day you come up with a simple but sturdy design and all you have to do is dig a hole for the run and shoot two parallel lines
Это на каком языке ?
Remember to use a nose and face shield. Fine wood dust are sucked up into the eyes, nose and mouth. They cause irritation of the lungs and can be severe.
А мне больше нравится, то, что было вначале
Технология распила забора на щепки от чемпион по идиотизму! 😂
🤡
Personally....i preferred the fence top b4 it was cut.....❤
THAT'S PRETTY TIGHT BUT IF YOU WANT TO DO A CUSTOM SCALLOP TOP CUT BOWED UP OR BOWED DOWN YOU CAN TAKE A 15 FOOT LONG FLAT THIN FIBERGLASS ROD AND TAP A NAIL ON ONE OF THE 4×4 POST ON ONE END AND THE SAME EXACT THING ON THE OTHER POST ONE INCH FROM THE TOP OF THE POST MEASURING DOWN FROM THE TOP OF THE POST AND TAP IN NAIL ABOUT HALFWAY AND THEN TAKE YOUR FIBERGLASS ROD AND IF YOU WANT DOWN SCALLOPS THEN GO TO THE CENTER OF THE SECTION OF THE FENCE AND TAP A NAIL AT THE CENTER POINT ONCE YOU'VE PULLED DOWN THE FIBERGLASS ROD TO ACHIEVE THE SCALLOP SHAPE AND TAP NAIL IN TO HOLD THE SCALLOP SHAPE AND TRACE YOUR ROD FROM END TO END WITH A GOOD PENCIL AND ONCE YOU DONE THAT THEN REMOVE FIBERGLASS ROD AND TAKE YOUR SAW AND FOLLOW YOUR LINE CUTTING FROM END TO END AND WHEN YOU GET DONE CUTTING YOU CAN STAND BACK AND LOOK AT YOUR NEW SCALLOP CUT FENCE AND JUST REPEAT IT ALL OF THE WAY AROUND THE WHOLE FENCE GOD BLESS ✝️✝️✝️
Когда есть инструмент и нет покоя от мысли ,что бы такого ещё снять и выложить
Why they cut it ?it looked nicer before.
It was the choice of the owner!!! To each their own!!!
Who gives a shit
Was probably over 6 feet, most states don't allow over 6 feet without a special permit.
Закон суров , но он закон 😅@@LupusRex-hf2rl
Might be installing Lattice
This is clearly in the US . Whoever pays the workers is the one that gives the orders
Why is this clearly in the US?
@@ChrisB0423 because the one that pays is the one that gives orders. It doesn't matter how the work looks as long as the one that pays likes it
@@JacintoJacobo-iw9xo okay. So that automatically makes it from the US. Very strange logic.
I don’t think any of you looked at the way the fence was constructed, there’s a backer rail below the top rail that they want to make the fence seamless for that style of fence.
Still wouldn't you agree that the spacing is off so when rain comes in that will swell and bow/warp the panels to make it moot?
Its also done with a cap so to protect the end of the one inch board from getting moisture, warping and cracking if the lumber isn't treated.
I don't think you saw two bi fours stacked one on top of the other that how that designed goes
If you look at then you will see it as far as treatment goes that's another story
I need that fence around 3.5 acres.
Коротко о технологии распила бюджета в любой стране мира.
He's screwing up that fence
No he's problem doing what the person paying for the fence wants.
It's not wrong I build fence for 15 yrs it's the style look at the finished part at the begining
@@marcussmith3969no way. never seen this
He cut to low...aint no style shown or any skill at that
@graffking-ru2wx no he didn't look at the finished fence
Take every board down and replace them with new ones . BTW, hire a new finish cut man the old one is FIRED ......😮
No, no don't trim. Looks BETTER as it was. Keep the additional inches to still serve as a divider.
A picture frame fence lasts longer in wetter environments like the US Deep South due to the boards end grains being covered by the top board.
So then, won't you please explain to me, how is it covered by the top broad? The top rail is next to it, not on top of it.
I take it you work with these illegals?
Freaking bonehead!
Same in Vancouver area. That original looks great but would look ghetto in 2 years.
This type of fence looks finished on both sides, as well, I believe.
Когда кончились дрова, можно подрезать забор соседа😂😂😂😂😂
Через неделю по новой можно забор устанавливать. 🤣
😅😅😅😅
The contractor’s job is to give THE CLIENT WHAT THE CLIENT WANTS!👍🏽
The before look was better than the after cut, you cut off a nice design.😮
Слишком высокий забор оказался за-за соседями подглядывать неудобно.
Ну вот , теперь понятно 😅😂😂😅
Сначала надо выровнять по верху концы, закруглить углы, чтобы не цеплять и потом пилить...
Очень технологично...
РУКИ КРЮКИ.
Так и положено делать, очень даже. 😂😂😂С перва асфальт, а потом водопровод... 😂😂😂😢
So what exactly was the point to go through all that lining the tops perfectly just to cut them, looked better with the dog ears on the top!!! 🤔🤔🤔🤔
@@donaldwhiteley1386 👌
You're either joking or you're high af
Now they can nail the top of the fence to the top band just under the top plate. Will look nice and finished out.
Mis respeto a estos maestros de la construcción
давай пили! - для буржуйки надо много красивых дров😂
За такое садить в тюрьму надо сколько леса в хлам.
Раньше сядет, раньше выйдет...
Мой забор, что хочу то и делаю.
Directly to jail
За убийство не сажают, а тут доски ...
Молодая пара выкинула в окно кресло и убили бабушку. Им дали год работ.
Не заплатили 😊
Bro was doing so good then that gap went from like 1/2” to like 2”. 😭
Чем выше забор ; тем лучше соседи.
Может быть дешевле доски заказать нужной длины?
ESO PENSE YO ,
ANTES DE LEER COMENTARIOS MÁS
TONTOS
EL QUE TIENE DINERO HACE LO QUE QUIERE
Having done fencing professionally, this was pretty cool and saves time on this type of fence build. The bottoms are nailed first, the tops stick up and are not nailed yet. When hes finished, he will come hack nail the tops and add a piece of trim horizontally along the top when they are finished.
The fact the fence height was nearly perfectly level in order to do that… amazing prep
И для чего ??
Because that is what the home owner ask for. No way would he be adding the extry labor had it not been requested by the person requested it and paying for his esrvice.
Чтобы легче было залезть в чужой огород. 😂😂😂
На дрова обрезки
I would have left the top alone
А мне понравилось- у забора появилась завершенность, он стал лучше смотреться, органичнее.
Customer comes home... I really like those lumpy tops that were on the fence.
Это как пузыри лопать,на упаковочной плёнке,трудно остановиться🤣🤣🤣 забор,за несколько заходов исчезнет🤣
Why is num nuts cutting dog ears off
Because the guy’s dumb nuts 😂
Yup....
LOL numb nuts cuz maybe the owner doesn't want them😂😂😂😂😂
I'm guessing he didn't get paid?
The question is how do you know if his nuts are numb? Have you been down there making them numb?
Great hand to eye coordination; steady hands, wonderful sighting!!!
They must be doing something special on this fence, would love to see the finish.
Какую-то дичь творит, что с людьми происходит. Вообще с ума посходили, что ли?
It looks better without trimming.
Mexicans and Hispanics in general, are the most dedicated hard working and most innovative workers in the world.
I agree, to me, the fence looked better before it was trimmed however it’s not my fence and I bet the customer was extremely happy with a job well done😎
чем больше строительных операций, тем больше денег с заказчика РУБЯТ😊
1) There must be a fence height restriction.
2) He had better be putting a piece of trim under that t-rail on top because that huge gap looks like shit.
No safety glasses, will go blind. Also, the beauty of the fence was taking away, I totally agree.
Thank God that fence in perfectly level. We need more guys like these hard working dudes
Это когда сосед построил забор выше нормы😂😂😂.
И зачем надо было отпиливать,ведь красиво было !!!
Может печку топить нечем.
Pretty slick, but personally, i preferred the castellated tops
Normally, you would cut the bottom of the board to maintain the dog-eared finish at the top, but this is a picture frame fence, so there will be a finishing board placed on top.
Так красиво было, сделаю у себя так же
Испортил забор. Окоротишь, хрен воротишь. Пусть живет с таким забором
You give the hardest task to the laziest man. He will figure out how to do it the easy way!
For those wondering why cut a perfectly top aligned top, there's another design top in its place. As you can see in the front as they finish the cut.
Если бы 7 раз отмерил, то можно было не соезать. То что срезал, теперь в утиль. А правильно бы омерил, то собрал бы ещё может 3 п.м. забора. Жопарукость.
He obviously doesn't have a clue as to what he's doing. You're not supposed to cut off the dog ears,
Never understand why hard working people don’t protect the eyes & ears ..🙂
Здесь всё просто,это тот самый момент «Когда заказчик засунул себе в очко деньги которые должен был по окончанию выполненных работ!»
The shit us carpenter's comes up with is insane, 😂😂
Не парься, просто вспомни людей, которые делают себе татуировки, а здесь просто забор.
Why did you spoil the fence, it looked better before you cut it, what a complete waste.
Времени не много ушло, а былую красоту не вернуть
Customer wanted it this way
Maybe its too high. Las is law
Скорее всего не заплатили. У нас в городе сруб раскатали по бревнышку и в кучу сложили😂
Look at it more closely. It goes under the top plate. They put the em on long with the tops bowing out. Watch as he cuts, the cut fence boards straighten out to be under the top plate.
You can disagree on which looks better, but the top plate is objectively better for the lasting longer. The top of the fence boards is end grain, which soaks up water and leads to damage over the long term. Covering the end grain will make the fence last much much longer.
Для такого инструмента есть заводская рамка (линейка) и не надо изобретать второй раз велосипед
Чем ему помешали эти верхушки? Всё было ровненько, красиво, однообразно. Там же видно, что торцы обработаны.
He's cutting it off because it sits inside the top rail.
No I think that's the woops part. I am thinking you not supposed to see the top real he cut on the wrong side of the top rail.
Somebody made a mistake.
Дураков везде хватает
Чем бы не заниматься лижбы заеб
Мастер! Все очень ровно и аккуратно получилось!
Раньше было красивее,вот так работают люди из ближнего зарубежья
Не практично, столько материала пускать на дрова и так всю сибирь вырубили
Где там всю выпилили? 😂😂😂 Ты там был?
Es mejor trabajar inteligentemente que trabajar duro
La guia podría ser más larga
Era mejor. ...... 😊
I liked it the way it was
And the tall curved ends made it difficult to climb over.
Este hermano Mexicano da mas orgullo que el Canelo.
I thought the fence looked better before with each board having that rounded corner look
Cuando las cosas no están bien medidas aky el pretexto romper y tirar lo k era útil como una barda completa con esos cortes k tenía cada tabla K DIRIA EL DUEÑO , ya k la madera es cara aunke está sea de 3a (por los muchos nudos k lleva)
Это надо же ради видео так заморочится закрепить доски по один уровень позади рейку закрепить под уровень и потом пилить циркулярной пилой с направляющей
Work SMART, Not make it harder for yourself!
Dahinter hat jetzt der 2m grosse Chef gestanden! 😂😂😂
Впервые вижу такое!
Дурная работа
Порнуха
The fence is not short this is a design they will cap the top and stain it or paint it and it will be a pannel style 😊 great work my friend perfect technique
There maybe many reasons to cut it down, but I can't understand why they didn't leave it like 75mm (3") longer to keep the top stringer covered? Looks to me many mistakes probably got made on this job
Wise man once told me to never saw anything that’s above my head with one hand.
Рукажоп, надо было мерить и нижнюю часть пилить если на то пошло, либо верхнюю планку не прибивать оставить как есть. Было бы на много лучше.
А если по высоте нарушает закон?
Not to mention, he's cutting it below the top rail
Not seen that done before. I like the header on top of the outrights. Good work
Соседский забор спиливает
А ни кто не заметил, что забором ограждают рабочую зону ? А доску на забор видимо закупили такой конфигурации. А для рабочей зоны, декор не нужен и забор должен быть типовым. Может по этому и делает обрезку. А ещё и рабочие с своеобразным мышление , по поводу красоты забора....😅 У меня других мыслей нет......😅
Hes actually putting a beautiful fence together, the video is in reverse
I seriously hope you are joking
As they say work smarter not harder
Ummm this is pretty much working completely stupid.
The furthest away from working smarter
Не понял, сразу после среза образуется плинтус
Только хотел написать что как-то странно выглядит 😮